Say you’ve just signed a lease on a Sydney office. The keys are in your hand, the team starts in eight weeks, and the budget looks solid. Then the builder asks to see the asbestos register, and nobody has one. That’s how plenty of commercial fitouts Sydney businesses kick off end up stalled before the first wall comes down.
Most expensive surprises start long before anyone picks a carpet. They come from an approval nobody checked, a lease nobody read, or a scope that stayed vague. Here are the mistakes worth dodging, and what to do about each one.
What Are the Costliest Fitout Mistakes?
In the order they usually bite:
- Budgeting from one headline cost per square metre
- Guessing at approvals instead of asking a certifier
- Starting work without seeing the asbestos register
- Signing a lease without reading the fitout and make good clauses
- Accepting a vague scope with exclusions buried in the small print
- Skipping contingency and booking the move-in date too early
Each one gets a section below. None needs a specialist to spot, just a bit of homework.
What Do Commercial Fitouts in Sydney Really Cost?
Mistake one is trusting a single number.
The price tag on commercial fitouts Sydney wide swings more than most people expect, and the published guides don’t agree because their dates and definitions differ. One independent Australian guide puts Sydney at roughly $800 to $3,500 per square metre, depending on specification, with base work at the bottom and a full tenant fitout at the top. Knight Frank’s research ranked Sydney as the most expensive Australian capital for office fitouts. JLL’s cost guide lists a national average of $2,810 per square metre. Cushman & Wakefield, meanwhile, describes the market as steadier after several years of climbing costs.
Run the maths on a 200 square metre office. At $800 per square metre, you’re at $160,000. At $3,000, you’re at $600,000. Same floor area, very different invoice.
Treat any per-square-metre figure as a conversation starter, not a budget. Ask each builder to price against the same written specification, then compare like with like. Honestly, that one habit saves more money than hard bargaining ever will.
Do You Need Approval for Commercial Fitouts in NSW?
Mistake two: assuming the answer is no. Or assuming it’s always a full development application. Both cost money.
NSW runs a few pathways. Very minor work can be exempt development, which needs no planning or construction approval if it meets the standards in the State Environmental Planning Policy (Exempt and Complying Development Codes) 2008. A lot of internal fitouts land in the next tier, complying development. The City of Sydney lists internal alterations or fit-outs of commercial buildings as one category, and either a council or a private certifier can determine the application. NSW Planning says an approval can be issued within 20 days when the proposal meets every relevant requirement. Applications go through the NSW Planning Portal.
The catch? Your project has to qualify. Internal alterations, changes of use, mechanical ventilation and shopfront work all sit under the Commercial and Industrial Alterations Code, but each has its own standards. Miss one, and you’re back to a development application.
Then there’s the finish line. A certifier issues the building approval and, once the work is done, the occupation certificate. For commercial buildings, newly installed fire safety measures also need their performance confirmed before anyone occupies the space. A removalist booked for Monday doesn’t change that.
My blunt advice: talk to a certifier before the drawings are final. A short conversation about the right pathway costs far less than redrawing plans after a knockback.
Is There Asbestos in Your Building?
Mistake three can halt a job outright. Ignoring asbestos. Plenty of commercial fitouts Sydney wide happen inside older buildings, which is exactly where this bites.
Australia banned asbestos from 31 December 2003. A workplace built before that date should have an asbestos register recording where it is and what condition it’s in. SafeWork NSW tells anyone working on a commercial building from before December 2003 to ask for a copy before starting. The WHS rules also put the duty on whoever manages the workplace, who must review the register and hand it to the business doing the refurbishment.
Picture a 1990s office floor with a tired ceiling. It looks harmless. But if the register flags possible asbestos up there, the builder has to plan around it before anyone pulls a single tile down. SafeWork NSW recommends using a licensed asbestos professional to remove any amount.
Ask the landlord or building manager for the register in week one, not week ten. And read SafeWork NSW’s asbestos guidance so you know what the process looks like before the builder raises it.
What’s Hiding in Your Lease?
Mistake four: locking in the design before reading the fitout and make good clauses.
A make good clause decides what you owe the landlord when you leave. The NSW Small Business Commissioner explains that these clauses typically require a tenant to hand the premises back in a similar condition to the start of the lease, and it suggests setting funds aside for the job. Wording matters, though. LegalVision, a law firm, notes that a general make good clause doesn’t automatically force a tenant to remove the fitout. In its view, the landlord has to require reinstatement expressly, ideally in writing when it approves the works.
Say you install glass partitions and a built-in reception desk. Three years on, the landlord wants a bare floor. Who pays to strip it out? If the lease and the approval letter are silent, you’re arguing. If they’re clear, you budgeted for it from day one.
On commercial fitouts in Sydney, get the landlord’s consent in writing, along with any building design rules and approval timeframes. Ask them to confirm the make good scope at the same time. And have a commercial leasing lawyer read the lease before you commit, because this article is general information, not legal advice.
Why Does a Vague Scope Blow the Budget?
Mistake five. A quote that just says “office fitout” next to a number is a guess dressed up as a price.
Cost guides keep flagging the same gap: Cat A versus Cat B. Cat A is the base fitout. Cat B is the full tenant fitout, and they’re very different scopes, so quotes aren’t comparable until the brief says which one you want. The same independent guide warns that small-print exclusions create most variations later, mainly authority approvals, after-hours labour and base-building upgrades. It also says the services trades (mechanical, electrical and fire) are where budgets move most.
Before you accept a quote, check that it states:
- Whether it covers Cat A or Cat B work
- Who pays for authority approvals and certifier fees
- How much after-hours work is included
- Which base-building upgrades are in or out, such as fire systems, ductwork and switchboards
- Joinery and furniture allowances, line by line
Look for commercial fitout specialists in Sydney who’ll walk you through the exclusions without sighing. If the scope is fuzzy, they’ll price the fuzz into variations later.
What Else Trips Up a Commercial Makeover?
A few smaller mistakes still sting.
- Zero contingency. Something always turns up behind a wall.
- Booking the move before the occupation certificate exists.
- Picking the lowest price without checking licences and insurance.
- Forgetting to arrange lift bookings, loading dock access and after-hours entry with building management.
- Leaving staff out of the layout conversation until the joinery’s already built.
Scale matters too. A tired reception area might only need office renovations. Moving walls, changing services or adding floor area is a different job, and a team offering commercial construction services can handle that structural side under one roof.
Hold a contingency line in the budget. I’d rather explain an unspent reserve than ask for more money halfway through a build.
What Should You Do First?
Order matters more than speed when you plan commercial fitouts Sydney wide. A sensible sequence:
- Read the lease and the landlord’s fitout rules.
- Ask for the asbestos register if the building predates 2004.
- Talk to a certifier about the approval pathway.
- Write the scope, including Cat A or Cat B, before anyone quotes.
- Collect quotes against that one document, then compare.
Follow that and most of the nasty surprises never get the chance to show up.
FAQs About Commercial Fitouts Sydney Business Owners Ask
How much does a commercial fitout cost per square metre in Sydney?
It depends on the specification. Published guides run from about $800 per square metre for base work to $3,500 or more for a full tenant fitout. Get every quote against one written scope so the numbers line up.
Do I need a DA for a commercial fitout in NSW?
Not always. Minor work can be exempt development, and many internal fitouts qualify for a complying development certificate, determined by a council or a private certifier. If your project doesn’t meet the Codes SEPP standards, you’ll need a development application. A certifier can tell you which pathway applies before you spend money on detailed drawings.
What’s the difference between Cat A and Cat B?
Cat A is the base fitout. Cat B is the full tenant fitout, and it costs a lot more.
Bottom Line
Most costly fitout mistakes happen before construction starts. Check the approval pathway, get the asbestos register, read the lease and pin the scope down in writing. Do those four things and the build itself gets much easier to price.
If you’re weighing up commercial fitouts Sydney offers right now, start this week. Ring a certifier. Ask for the register. Open the lease and find the make good clause.